中文 电脑版

Reciprocating pump technology · 12–600 m³/h · up to 3,150 m head

High-pressure pumps that cut your energy bill — not your uptime.

Multi-plunger reciprocating pumps and slurry pumps built for continuous duty in mines, power plants, oilfields and processing plants. 90%+ efficiency, direct mechanical drive, and drop-in replacement for multistage centrifugal pumps.

Send your duty pointSize a pump in 30 seconds

90%+Pump efficiency, stable in service

12–600m³/h flow range

4–50MPa discharge pressure

30,000 hOverhaul interval

What we build

Two product families, one engineering approach

Mechanical direct drive instead of a hydraulic power pack. Fewer failure points, higher efficiency, and a footprint that drops straight into your existing pump house.

UDZ series · 3 / 5 / 7 plungers

Multi-plunger high-pressure pumps

Multi-plunger high-pressure reciprocating pump installed in a pump house

UDZ series · 3 / 5 / 7 plungers

Multi-plunger high-pressure pumps

12–600 m³/h and 200–3,150 m of head (2.0–31.5 MPa), plus an injection series to 70 MPa, all with efficiency above 90%. Used for boiler feed, oilfield water injection, high-pressure descaling and mine dewatering. Same suction and discharge orientation as the multistage centrifugal pump it replaces — a 500 m³/h centrifugal pump is replaced by one UDZ 600 unit, not a parallel pair.

Explore the UDZ series →

V5 · vertical five-plunger

Slurry pumps for abrasive duty

V5 vertical five-plunger slurry pump

V5 · vertical five-plunger

Slurry pumps for abrasive duty

100–400 m³/h up to 150 m head, handling solids above 30% by weight. Ceramic plungers and alloy valve seats take the wear that destroys centrifugal slurry pumps, at more than 83% efficiency.

Explore the V5 slurry pump →

New product lines

Oil-free air, mobile water, on-site intelligence, efficient drive

Four additions to the pump business: levitated-rotor blowers and vacuum pumps, self-contained mobile pump units, an industrial AI appliance that runs on the plant network, and the motors that drive all of it.

Maglev / air-foil

High-speed blowers & vacuum pumps

◍

18.5–750 kW magnetic-bearing blowers, 15–300 kW air-foil units, compressors to 500 kPa. No oil, no gearbox, 85%+ efficiency — where a Roots blower manages under 65%.

See the ranges →

Mobile units

Portable and trailer-mounted pump sets

◫

Emergency dewatering, flood response and temporary transfer. Diesel or electric, quick-connect pipework, running the same day it arrives.

See the formats →

Motors

IE3–IE5 induction & PM synchronous

◉

0.12–375 kW at 380 V and 160–2,500 kW at 6/10 kV, plus permanent-magnet synchronous motors to 450 kW. Same IEC frames — a higher efficiency class drops onto the existing baseplate. Supplied on its own for replacement, or as part of a pump train.

See the type spectrum →

Edge AI

Industrial AI agent appliance

⌁

A 27B language model and the OpenClaw agent runtime running on site. Four concurrent sessions, 40+ tok/s in total, about 58 W — no cloud, no data leaving the plant.

See the specification →

Where they run

Built for the duties that eat pumps

Mine dewatering

⛏

Multi-stage lift from underground sumps to surface, at pressures centrifugal pumps cannot hold.

Read more →

Filter press feed

▤

Stable high pressure through the whole fill cycle, so cakes form faster and drier.

Read more →

Tailings & coal slime

≋

High-density slurry transport without the wear-and-replace cycle of centrifugal slurry pumps.

Read more →

Oilfield water injection

◎

120–500 m³/h at 16–25 MPa, with specific power down to 0.3 kWh/m³·MPa.

Read more →
Efficiency you can measure, maintenance you can plan

Why operators switch

A multistage centrifugal pump in abrasive or high-pressure service typically runs at 45–65% efficiency once wear rings open up. A positive-displacement plunger pump holds 90%+ because its volumetric efficiency does not depend on fine clearances.

  • Direct mechanical drive. No hydraulic power pack, no high-speed friction pairs, no oil overheating in summer.
  • Drop-in retrofit. Matches the piping orientation of the centrifugal pump, so the change is a swap — not a rebuild.
  • Predictable wear. Plungers, valve seats and seals are consumables with published intervals; the crank, crosshead and frame are not.
  • Smart control. VFD, condition monitoring, fault diagnosis and remote data as an option on every unit.

Field reference

Shengli Oilfield — Wanggang injection station

Seven-plunger reciprocating injection pump commissioned in August 2023 and running continuously since. Specific power measured at 0.3 kWh/m³·MPa against 0.5–0.8 for the multistage centrifugal units it replaced.

Configuration7-plunger, VFD

Duty120–500 m³/h · 16–25 MPa

StatusIn continuous service

Machines in service, not renders

Track record

Reciprocating pump installations in gold mines, coal mines, oilfield injection stations and waste-heat boiler houses. Measured duty points, measured power, written reports.

Underground mine pump house with reciprocating pumps
Coal mine dewatering — three pump houses at −50 / −250 / −500 m, six machines replacing 24 multistage centrifugal units
High-pressure pump station piping
High-pressure discharge pipework, 6.5 MPa lift to the 170 m level
Shengli Oilfield water injection station
Shengli Oilfield — Guanqi and Wanggang water-injection stations, seven-plunger units
Slurry pump close-up
V5 slurry pump — ceramic plungers and alloy valve seats for abrasive duty

26.7%Energy saving, coke dry quenching waste-heat boiler feed

22–37%Energy saving, mine dewatering retrofits

0.3kWh/m³·MPa specific power, oilfield injection

30,000 hOverhaul interval on the crank and frame

See references and test reports →

Test reports you can read before you buy

Documentation

Site test reports from operating installations, with flow, pressure, power and specific energy recorded on site. Full PDFs are available below.

Reference data summary sheet

Download PDF →

Site test report, 270 m level

Download PDF →

Site test report, 51 m level

Download PDF →

Send us a duty point, get a selection.

Flow, head or pressure, fluid and temperature — that is enough to start. We answer with a model, a curve and a budgetary price.

Request a quotation
Multi-plunger pumpsSlurry pumpsMaglev blowersMobile pump unitsMotors IE3–IE5VFD motorsIndustrial AI box

大连宏实科技有限公司 · DALIAN HONGSHI TECHNOLOGY

Related sites Fluid machinery energy-saving calculator·KSTS — biogas & bioenergy, Sabah

jeeftang@hschina.com

© 2026 · Mobile edition · 手机版

⌂Home ✉Get a quote