中文 电脑版

Portable pump · axial-flux canned motor

A 2.7 kg pump that lifts water 62 metres

Axial-flux motor and impeller built into one sealed body: 8,000 L/h, 62 m of head, IP68, no shaft seal and no oil. Carried by hand, run from a 72 V battery pack, a vehicle supply or the mains, and adjusted from a phone.

Portable axial-flux pump unit in use outdoors
120 × 120 × 90 mm, 2.7 kg without cable — one hand, one hose.

The seal is the part that fails

On a conventional pump the shaft passes through the casing, and a mechanical seal keeps the water out of the motor. That seal is the first thing to wear, the first thing to leak, and the reason a small pump cannot be left running unattended.

This unit has no shaft. The rotor turns inside a thin can, the stator sits outside it, and the water never meets anything that can leak. No seal, no lubricant, no drip tray.

Dry-run tolerant, corrosion resistant. Impeller and housing in high-strength PPS, bearings in silicon carbide. Handles coolants and mildly aggressive fluids without a coating that can flake.

Specification

One model, one set of numbers

← 左右滑动查看完整表格 / swipe to see all columns
ParameterValueParameterValue
Rated power2 kWVoltage220 / 110 / 72 V
Maximum flow8,000 L/h (8 m³/h)Maximum head62 m (two units in series: 124 m)
Rated speed7,500 rpmProtectionIP68 — submersible
Dimensions120 × 120 × 90 mmWeight2.7 kg without cable
Noise at rated load< 65 dBMedium temperature−20 to +60 °C
Ambient−20 to +60 °C, RH < 90%ConnectionsRC 3/4 internal, RC 1" external
Impeller / housingHigh-strength PPSBearingsSilicon carbide
Air tightness1 MPa test, leakage < 1 mL/minControlVariable speed, WiFi app

Performance is quoted at the rated voltage. Flow and head trade against each other along the published curve — send the duty point and we will confirm the operating position before you order.

Why it is built this way

Fewer parts, fewer failures

No shaft, no seal

◍

The rotor is the only moving part and it is fully enclosed. Nothing to repack, nothing to drip, no seal to replace on a schedule.

Axial-flux motor

⌁

A flat motor of high power density built into the pump body — that is why a 2 kW machine fits in the palm of your hand.

Sealed for immersion

▤

IP68 rated, so it can be dropped into a tank as a submersible, or bolted into a line as a booster, with the same unit.

Variable speed

◷

Integrated controller with stepless adjustment. Turn the flow down instead of throttling a valve and wasting the difference.

Phone control

✦

WiFi app for start/stop, speed and irrigation schedules — useful where the pump is somewhere you would rather not walk to.

Quiet

◎

Under 65 dB at rated load, with no gear mesh and no cooling fan screaming at 7,500 rpm.

Where a hand-carried pump earns its place

Applications

Six duties this unit was built for — and the reason it is kept charged and ready rather than stored in a shed.

Vehicle and outdoor

Runs from a portable power station in the truck or camper. Water transfer, washing down, drawing from a stream or tank.

Irrigation

Factories, gardens, estates, farms, schools, hospitals, nurseries, livestock. Scheduled watering from the app, with flushing duties in between.

Food and beverage

Clean fluids — milk, soy, drinks — where a leaking seal would be a contamination event rather than a maintenance ticket.

Pressure boosting

Wells, hillside villas, guesthouses, upper floors and hot-water circulation. One unit gives 62 m; two in series give 124 m.

Marine

Deck and hold washing, bilge transfer, auxiliary fire duty on small and medium vessels.

Emergency response

Narrow lanes and rural sites a fire appliance cannot reach, and post-flood flushing of silt and contamination.

One unit, four ways to install
  • Submersible. Dropped into a tank, sump or well — IP68 and small enough to pass a manhole.
  • In-line. Bolted into pipework as a transfer or circulation pump.
  • Booster. Added to an existing supply to lift pressure at the top of a building.
  • Portable set. Carried with a battery pack and a hose reel as a standalone unit.

The same body works in all four because there is no seal to orient and no oil to keep level. Vertical or horizontal, it does not care.

Portable pump unit close-up

Supply scope

  • Pump unit with integrated controller
  • Mains adapter, or 72 V DC lead for battery operation
  • Hose tails to RC 3/4 and RC 1"
  • WiFi app setup and operating manual
  • Spare parts: impeller, bearing set, controller

OEM & private label

Supplied under your brand, if that is what you need

Every machine on this page can be built to order under the nameplate of a distributor, integrator or project contractor: documentation, packing, paint scheme and label set to your specification. Certification, where a market requires it, is applied for against the brand and the market it will be sold in — we do not pass off one market's approval as another's.

Tell us the lift and the volume.

Height from water level to outlet, litres per hour you need, and what power is available. We will confirm whether one unit does it or two in series.

Request a configuration
Multi-plunger pumpsSlurry pumpsMaglev blowersMobile pump unitsMotors IE3–IE5VFD motorsIndustrial AI box

大连宏实科技有限公司 · DALIAN HONGSHI TECHNOLOGY

Related sites Fluid machinery energy-saving calculator·KSTS — biogas & bioenergy, Sabah

jeeftang@hschina.com

© 2026 · Mobile edition · 手机版

⌂Home ✉Get a quote