Reciprocating pump technology · 12–600 m³/h · up to 3,150 m head

High-pressure pumps that cut your energy bill — not your uptime.

Multi-plunger reciprocating pumps and slurry pumps built for continuous duty in mines, power plants, oilfields and processing plants. 90%+ efficiency, direct mechanical drive, and drop-in replacement for multistage centrifugal pumps.

90%+Pump efficiency, stable in service
12–600m³/h flow range
4–50MPa discharge pressure
30,000 hOverhaul interval

What we build

Two product families, one engineering approach

Mechanical direct drive instead of a hydraulic power pack. Fewer failure points, higher efficiency, and a footprint that drops straight into your existing pump house.

Multi-plunger high-pressure reciprocating pump installed in a pump house

UDZ series · 3 / 5 / 7 plungers

Multi-plunger high-pressure pumps

12–600 m³/h and 200–3,150 m of head (2.0–31.5 MPa), plus an injection series to 70 MPa, all with efficiency above 90%. Used for boiler feed, oilfield water injection, high-pressure descaling and mine dewatering. Same suction and discharge orientation as the multistage centrifugal pump it replaces — a 500 m³/h centrifugal pump is replaced by one UDZ 600 unit, not a parallel pair.

  • No hydraulic station — mechanical crank drive
  • Wear parts 5,000 h+, overhaul 30,000 h+
  • On-site maintenance, no factory return
Explore the UDZ series →
V5 vertical five-plunger slurry pump

V5 · vertical five-plunger

Slurry pumps for abrasive duty

100–400 m³/h up to 150 m head, handling solids above 30% by weight. Ceramic plungers and alloy valve seats take the wear that destroys centrifugal slurry pumps, at more than 83% efficiency.

  • Efficiency 83%+ vs 25–50% for centrifugal slurry pumps
  • Ceramic plunger + alloy valve seat
  • Wear parts 4,000 h+, overhaul 30,000 h+
Explore the V5 slurry pump →

New product lines

Oil-free air, mobile water, on-site intelligence, efficient drive

Four additions to the pump business: levitated-rotor blowers and vacuum pumps, self-contained mobile pump units, an industrial AI appliance that runs on the plant network, and the motors that drive all of it.

◍

Maglev / air-foil

High-speed blowers & vacuum pumps

18.5–750 kW magnetic-bearing blowers, 15–300 kW air-foil units, compressors to 500 kPa. No oil, no gearbox, 85%+ efficiency — where a Roots blower manages under 65%.

See the ranges →
◫

Mobile units

Portable and trailer-mounted pump sets

Emergency dewatering, flood response and temporary transfer. Diesel or electric, quick-connect pipework, running the same day it arrives.

See the formats →
◉

Motors

IE3–IE5 induction & PM synchronous

0.12–375 kW at 380 V and 160–2,500 kW at 6/10 kV, plus permanent-magnet synchronous motors to 450 kW. Same IEC frames — a higher efficiency class drops onto the existing baseplate. Supplied on its own for replacement, or as part of a pump train.

See the type spectrum →
⌁

Edge AI

Industrial AI agent appliance

A 27B language model and the OpenClaw agent runtime running on site. Four concurrent sessions, 40+ tok/s in total, about 58 W — no cloud, no data leaving the plant.

See the specification →

Where they run

Built for the duties that eat pumps

⛏

Mine dewatering

Multi-stage lift from underground sumps to surface, at pressures centrifugal pumps cannot hold.

Read more →
▤

Filter press feed

Stable high pressure through the whole fill cycle, so cakes form faster and drier.

Read more →
≋

Tailings & coal slime

High-density slurry transport without the wear-and-replace cycle of centrifugal slurry pumps.

Read more →
◎

Oilfield water injection

120–500 m³/h at 16–25 MPa, with specific power down to 0.3 kWh/m³·MPa.

Read more →

Why operators switch

Efficiency you can measure, maintenance you can plan

A multistage centrifugal pump in abrasive or high-pressure service typically runs at 45–65% efficiency once wear rings open up. A positive-displacement plunger pump holds 90%+ because its volumetric efficiency does not depend on fine clearances.

  • Direct mechanical drive. No hydraulic power pack, no high-speed friction pairs, no oil overheating in summer.
  • Drop-in retrofit. Matches the piping orientation of the centrifugal pump, so the change is a swap — not a rebuild.
  • Predictable wear. Plungers, valve seats and seals are consumables with published intervals; the crank, crosshead and frame are not.
  • Smart control. VFD, condition monitoring, fault diagnosis and remote data as an option on every unit.

Field reference

Shengli Oilfield — Wanggang injection station

Seven-plunger reciprocating injection pump commissioned in August 2023 and running continuously since. Specific power measured at 0.3 kWh/m³·MPa against 0.5–0.8 for the multistage centrifugal units it replaced.

Configuration7-plunger, VFD
Duty120–500 m³/h · 16–25 MPa
StatusIn continuous service

Track record

Machines in service, not renders

Reciprocating pump installations in gold mines, coal mines, oilfield injection stations and waste-heat boiler houses. Measured duty points, measured power, written reports.

26.7%Energy saving, coke dry quenching waste-heat boiler feed
22–37%Energy saving, mine dewatering retrofits
0.3kWh/m³·MPa specific power, oilfield injection
30,000 hOverhaul interval on the crank and frame

See references and test reports →

Documentation

Test reports you can read before you buy

Site test reports from operating installations, with flow, pressure, power and specific energy recorded on site. Full PDFs are available below.

Reference data summary sheet
Reference data summaryTwo mine levels, measured before and afterDownload PDF →
Site test report, 270 m level
Site test report — 270 m levelMine dewatering, reciprocating pumpDownload PDF →
Site test report, 51 m level
Site test report — 51 m levelMine dewatering, reciprocating pumpDownload PDF →

Send us a duty point, get a selection.

Flow, head or pressure, fluid and temperature — that is enough to start. We answer with a model, a curve and a budgetary price.

Request a quotation